澳门新葡亰平台5197-首页

澳门新葡亰平台5197

【中英文】波纹补偿器安装说明“简单实用”

来源:【中英文】波纹补偿器安装说明“简单实用” 发布于:2018-11-14 11:25   浏览:
【中英文】波纹补偿器安装说明“简单实用”
The installation of corrugated compensator is simple and practical.

澳门新葡亰平台5197官方网站为您先容:【中英文】波纹补偿器安装说明“简单实用”信息,淞江集团为网友分享波纹补偿器中英文版本的安装说明,方便大家进一步了解和学习波纹补偿器常识,以下是详细先容。
The official website of Shanghai Songjiang Shock Absorber Group Co., Ltd. will introduce to you: [Chinese and English] The installation instructions of corrugated compensators are "simple and practical" information. The installation instructions of Chinese and English versions of corrugated compensators are shared by Songjiang Group for netizens, which will facilitate you to further understand and learn the knowledge of corrugated compensators. The following is a detailed introduction.

【中英文】波纹补偿器安装说明“简单实用”

Key factors for installation
安装的关键因素
 
Following advises are however to be taken into consideration in order to obtain a good performance and prolonged service life of the expansion joint.
注意:为了获得良好的性能和延长补偿器的使用寿命,必须考虑以下建议。

Fixed points
固定点
 
An expansion joint acts as a piston by the forces arising from the internal pressure.To prevent the pipes from damage they are to be properly anchored in order to take care of these reaction forces (Fr).
波纹补偿器由内部压力产生的力作用于活塞,为了防止管道受到损坏,必须将管道固定起来,以处理这些反作用力(FR)。
 
The Reaction force of an expansion joint is calculated by the following formula:
波纹补偿器的反力计算公式如下:
Fr = Q x P x 0.01
Fr = reaction force in kN.
Q = effective cross sectional area in cm2.
P = actual pressure in bar or kp/cm2
 
Mounting
安装
 
Before installation, the temperature, pressure and displacement of the product should be strictly used.
安装前应严格在产品允许的温度、压力和位移量范围内使用!
 
The expansion joints shall be easily accessible and open to regular supervision. Lt is recommended to let the expansion joints work in compression rather than stretching. Torsion is not permitted.
波纹补偿器应该定期检查。我建议波纹补偿器的工作是压缩,而不是拉伸,更不允许扭转和横向位移。
 
Maintenance instructions: observe whether the expansion jointt is over stretched and keep the expansion joint in normal length every month.
保养须知:每月要观察波纹补偿器是否超位移拉长,保持波纹补偿器在正常长度内使用。
 
In order to ensure the expansion capacity, the bolts should be kept as small as possible (not exceeding 2 mm or 3mm) to avoid damaging the metal hose body.
为了保证伸缩能力,装配螺栓要确保螺纹螺栓尽量少(不超过2毫米或3mm),以避免损坏波纹补偿器本体。

Precaution
预防措施
 
When welding work is to take place the bellow has to be protected from welding heat and sparks.
当焊接工作发生时,波纹补偿器本体必须防止焊接发热和火花。
 
Please install an effective chlorine removal device at the inlet of the pipeline (chloride content is not more than 25mg/l) to avoid excessive chlorine content and pinhole corrosion.
请在管道进水口加装有效去除氯离子装置(氯离子含量不超过25mg/l),避免水氯离子含量超标,产生针孔腐蚀。

澳门新葡亰平台5197
Shanghai Songjiang Shock Absorber Group Co.,Ltd.


相关下载:









最新推荐:
·整批螺纹橡胶接头发货现场“高品质” ·液压橡胶管接头在风力发电的作用
·如何打造海洋极地世界维生系统? ·Demag住友德马格创于德国:注塑机制造商
·美国PROCO膨胀节PROCO补偿器“补偿管道偏离偏距” ·【青海珠峰冬虫夏草工厂】金属软管合同
·三种有效水质处理方式:游泳池水处理系统 ·橡胶接头工厂事故应急池先容
·小区变压器太吵睡不好怎么办?降噪神器矩阵式减震器 ·【大连湾刘屯旧区改造项目】变压器减震器合同
在线咨询

澳门新葡亰平台5197|澳门新葡亰

XML 地图 | Sitemap 地图